steptail.com

If I try to fail, but succeed, which one did I do?

User Tools

Site Tools


toshiba_t-series_support:toshiba_t3200sx

T3100 | T3100e | T3100SX | T3200 | T3200SX | T3200SXC | T5200 | T5200C

Toshiba T3200SX

The Toshiba T3200SX

A durable workhorse of it's time, the T3200SX and T3200SXC portable computers were manufactured and targeted primarily as desktop replacement computer for businesses. Of course, at the time of the release, there existed smaller laptop computers, but none of these even came close to the power, durability and expandability of this Toshiba computer.

The T3200SX and T3200SXC are siblings. The only major differences are that the SXC has a color flat panel screen and a faster CPU (20 MHz as opposed to 16 MHz). The graphics adapters are the same, both systems are VGA capable, and support resolutions up to 640×480 with 16 colors.


Technical Specifications
Year Announced 1989
Processor 16MHz Intel 80386SX-16
Coprocessor Optional 80387SX-16 math co-processor, such as Cyrix CX-83S87-16-KP
RAM Standard 1 MB of RAM, expandable up to 13 MB.
Hard disk T3200SX comes standard with a Conner CP-model IDE hard disk, either 40 MB or 80 MB (BIOS selectable)
T3200SX/120 comes standard with a Conner 120 MB IDE hard disk.
Floppy disk 3,5“ 1.44 MB High Density (HD) diskette drive
Video Adapter VGA compatible WD 90C21 chip with 256 KB video RAM with VGA output.
Internal display 11.2” flat panel orange/amber plasma display with 640 by 480 native resolution and 16-level gray scale.
I/O Ports 1x VGA, 1x Parallel, 2x RS232C Serial, 1x DIN keyboard connector.
Internal expansion slots 1x full size 16/8-bit ISA slot
1x half-size 8-bit ISA slot
Power Supply Universal. Works with 110V/220V and 50/60 Hz power.
Dimensions 370 x 395 x 99 mm (W x D x H)
Weight 7.9 kg (17.4 lbs)
Known model numbers T3200SX (EU): PA8045E
T3200SX (US): PA8045U
T3200SX/120 (US): PA8046U
Other features
Software
Operating System Toshiba MS-DOS 4.01
Toshiba MS-DOS 3.3
OS/2 1.1
T/PIX 2.1 (AT&T UNIX System V/386 R3.0 (option)

System Boot process

System Expansion

Hard disk

Toshiba T3200SX comes with either a 40 MB or a 80 MB hard drive. As far as I understand, there was also a T3200SX/120 which was a upgraded model, and comes with a 120 MB hard disk. The system has a standard IDE interface to connect to the supplied Conner CP hard disk.

These are the drive configurations supported by standard T3200SX BIOSes:

Model Native C/H/S1) BIOS reported C/H/S2) Capacity Seek time
C H S C H S MiB MB
Conner CP-30003) 1045 2 40 862 2 48 40 MB 43 MB 28 ms
695 7 17
Conner CP-30444) 1047 2 40 980 5 17 40 MB 43 MB 25 ms
Conner CP-xxxx :?: :?: :?: 981 10 17 81 MB 85 MB Unknown
695 14 17 80 MB 85 MB
862 4 48 80 MB 85 MB

These configurations are supported by T3200SX/120 (with at least the 003F BIOS):

Model Native C/H/S5) BIOS translated C/H/S6) Capacity Seek time
C H S C H S MiB MB
Conner CP-30447) 1047 2 40 980 5 17 40 MB 43 MB 25 ms
Conner CP-301048) 9) 1524 4 39 762 8 39 120 MB 122 MB 19 ms

Search these hard drives on eBay 10)

I'm missing the part number of the 80 MB Conner hard disk. If you know it, please let me know!

This system can be expanded with an 8-bit and 16-bit ISA expansion cards. Hence, you can purchase an XT-IDE adapter to add a hard drive, such as the XT-CF-MINI or XT-CF-Lite card to add a Compact Flash card as a hard drive. They usually run for $40-$60. You can find them on eBay. Check out http://www.malinov.com/Home/sergeys-projects/xt-cf-lite and https://shop.bluelavasystems.com/products/xt-cf-mini-bootable-8-bit-isa-cf-card-interface-xt-ide

Another option is to purchase an XT-IDE adapter for the Toshiba proprietary expansion slot. There is a maker on eBay that sells Toshiba type expansion cards with XT-IDE to allow many different types of IDE and CF cards to be used on the portable computer. Please see the following link for the sales article. 3inONEder: Toshiba Portables (affiliate link)

Audio and ethernet

The same adapter that allows you to use the Toshiba proprietary slot connector for XT-IDE and custom hard disks also optionally allows to add audio (Adlib) and ethernet support (partially NE2000 compatible). Please see the following link for the item page. 3inONEder: Toshiba Portables (affiliate link)

CPU upgrades and overclocking

I've been informed that it is possible to replace the CPU with a TX486SLC upgrade, however this will require soldering. Credits for this discovery go to mohhingman. Thank you!

RAM memory upgrade

The computer uses 30 pin SIMM modules to add more system memory, but as far as I know they are proprietary Toshiba specific modules. The computer was shipped with 1 Mb (megabit) or 2Mb memory chips that were 80ns (or faster) and have parity. There are six slots in total and the banks are used in pairs, so at least two are needed. Standard configuration comes with 2 MB of RAM preinstalled, upgrade models come with 4 MB. The memory is upgradable up to 13 MB 11)

ISA Expansion Slots

If you remove the rear panel, you will be able to access the ISA expansion slots. The computer has one 16-bit full-length ISA slot and one 8-bit half-length ISA slot. The system also has a proprietary 16-bit Toshiba expansion slot. I have my computer set up with an 16-bit Sound Blaster 16 and an 8-bit 3Com Etherlink III (3C509) for networking. However, at least this site 12) points out, that not all newer 3Com Etherlink III cards support 8-bit ISA.

Math coprocessor (FPU)

The computer can be upgraded with an math coprocessor (FPU). The FPU doesn't come as standard, but the computer has a provision for an added Intel or compatible 387 FPU. One computer that I repaired had the Cyrix CX-83S87-16-KP FPU installed.

AT keyboard connector

The computer has a DIN connector for a AT style keyboard but it may be covered by a plastic cap. Please see the DIN keyboard connector page for more information.

CMOS clock battery

Lithium 3.6V battery supplied. A T3200SX/120 I had came with an original Tadiran TL-5207 3.6V battery. It had a plastic container package, that actually just contained a Tadiran TL-5151 3.6V 1/2 AA lithium battery. Please see gallery for more pictures.

Questions and Answers

Q: What is the PRN-A-B Switch on the side?
A: Toshiba offered an external 360Kb disk drive as an option. This plugs in to the parallel port connector but is not a parallel device. Setting the switch to PRN enables the printer port, setting it to A tells the machine there is an external disk drive and you want it to be A drive. Setting it to B tells the machine there is an external disk drive and you want it to be B drive. Setting it to A would allow you to boot 360Kb boot disks.

Unless you have the Toshiba external floppy – always set this to PRN. 13)

Q: Can't boot from floppy, floppy not detected, or can't be read
A: Make sure the PRN-A-B switch is set to PRN (see above question about PRN-A-B switch.

Q: My computer gives me a configuration error when I turn it on
A: If the CMOS battery is empty, you will be prompted with the following error when you power on the machine.

Invalid configuration information - please run SETUP program
 Strike the F1 key to continue. F2 to run the setup utility

Please refer to instructions here:
How do I boot my T3200SX with an empty CMOS battery

Q: How can I access the built-in BIOS ?
A: Press CTRL + SHIFT + F10 when the computer powers on. If this does not work, you may use the TEST3.EXE utility, a little program by Toshiba which will open up the BIOS settings from a DOS environment. You might want to include this utility in your computer recovery disk. See below for files that apply to this type of machine, or view all files at the files and resources section.

Q: I am still unable to access the BIOS.
A: When the computer BIOS battery runs empty, it will clear all BIOS settings and will prompt you to review the system settings on power-up. This may be used to your advantage to get into BIOS. To force this behavior, disconnect the clock battery entirely. Wait for a few minutes and power up the computer again. The computer will ask the user to review the default settings. Please refer to How do I boot my T3200SX with an empty CMOS battery

Q: My computer does not hold settings or time
A: You probably have an empty BIOS battery. The battery holds volatile information in a CMOS chip like information about your BIOS settings and system time. When the battery runs out, the information will be lost. You can still use your computer by going into BIOS settings and accepting the defaults (see above).

Q: How do I replace the computer BIOS battery?
A: The BIOS battery header is located on the system board. The battery is traditionally tucked in at the back of the floppy drive. The correct voltage for the battery is 3.6V. There are two ways that I've seen the battery been replaced.

1. You can remove the old battery. Cut the leads at the battery terminals, and get a replacement battery, for example a ER14505 3.6V lithium battery, sold new at eBay and other sources. You will also need a single AA battery holder for the new battery. Depending on your computer, your old battery might have included a 330 ohm resistor in line at the negative pole and you will want to leave that in place. In most cases your setup will look something like this:
[MB + ]—————-[ + ER14505 BATT - ]——–[ 330R ]—————-[MB - ]

2. Alternatively, you can replace it with a 3.0V CR2032 coin cell battery. In this case you should buy a CR2032 holder, a CR2032 lithium battery and a diode. The diode may be required to avoid charging the battery. You can measure the voltage at the motherboard to see if it has a charging voltage while the computer is powered on. If it does, use the diode. Take the old battery connector and its wires, solder the coin cell holder to the wires and solder the diode in series as such:
[MB + ]—————-[|<]——–[ + CR2032 BATT - ]——————[MB - ]

You may search for CR2032 battery holders including leads using this eBay affiliate link

Q: How do I upgrade the Hard Disk?
A: It depends on the BIOS version of your Toshiba portable (see below for instructions how to check the BIOS version). Most Toshiba T3200SX BIOSes are restricted to CONNER hard-drives of either 40 or 80 megabytes size (T3200SXC will be either 40 or 120 MB). On boot-up, the BIOS queries the IDE controller for hard-drives, and depending on your BIOS version, one of two things will happen:

  1. Older Toshiba BIOS (such as 003C)
    1. The computer will detect any drive and just assume it's a 40 MB disk (regardless of its actual size).
  2. New Toshiba BIOS (such as 003E-003I)
    1. The computer will not boot an unsupported drive unless it is manufactured by Conner. It will assume it's a 40 MB drive (regardless of its actual size). If you have a different drive than Conner, the computer will simply refuse to boot from the hard disk. The model/part number reported to the computer must match the letters 'CP' (Conner Peripherals) for it to be detected.

You have a couple of options:

  1. If the computer has the older BIOS such as the 003C, the computer should ignore the part number and will attempt to boot the hard disk regardless, even with incorrect settings. However, since the settings are fixed, you can not use more than the amount of space specified in the BIOS, which is only 40 MB. To override the BIOS limitation and use more space on the disk, so you will need to manually correct the settings on boot using a drive overlay software which is installed on the hard disk. I have tested a program called Anydrive, and I believe Western Digital's EZ-Drive version 9.03W will work as well. Both programs can be found in the files section. Anydrive overrides the BIOS settings so you can use any size hard disk (or CF memory card with CF to IDE adapter) up to 504 MB. With EZ-Drive you can potentially use larger disks, but run the risk of disk file corruption above 4 GB.
  2. If you have the newer BIOS, you can do the following:
    1. Buy a BIOS ROM chip drop-in replacement. Please see my Replacement BIOS ROM chips section for more information how to buy.
    2. Buy a compatible Conner hard-disk. The compatible part numbers are listed above.
  3. If you have an EEPROM programmer, such as the Minipro TL866, you can make your own BIOS chip and replace the problematic one by using HighTreason's excellent tutorial. Programming a compatible BIOS will allow you to boot with any hard disk, and then simply install a hard disk overlay program to override the drive parameters with correct ones. The tutorial, associated ROM images and HDD overlay programs are in the Files and Resources page.
  4. You can also buy an XT-IDE adapter, such as the XT-CF-lite from Lo-Tech. TexElec carries these in stock in the US. This will bypass the built-in IDE controller completely and replace it with a CF card. You can then set your BIOS to “No drive”.

Note: If you plan to use a drive other than what was supplied with your computer, you must use a BIOS HDD overlay software to avoid data corruption.

Q: I upgraded the hard disk on my Toshiba, but now it refuses to boot, or doesn't detect the hard disk.
A: If you have verified the replacement disk is fully working, then your computer must be using a BIOS version that only detects and supports Conner hard disks. See above for details.

Q: How do I check the BIOS version?
A: You need to open the portable computer. Remove the four screws from the bottom front of the laptop. Open the screen lid. The keyboard should now lift up starting from the front. You may need to pry the keyboard a little. Once the keyboard is off, remove two screws at the rear of the EM shield between the keyboard and the motherboard. Remove the EM shield. You will see three chips. The one at the bottom right corner is the BIOS chip. So far I've seen 003C, 003E, 003F, 003H and 003I out in the wild. If you have a different BIOS version, please take a picture of it and send a BIOS dump over! I will gladly host it on this site.

Q: I've opened the laptop, but I cannot move the flat panel display out of the way
A: The Toshiba portable computer can be tricky when you're trying to open the laptop after you've removed the keyboard, EM shield and now want to have access to the hard drive, floppy drive or other connectors. If your laptop has never been opened, chances are there is a latch that has been screwed in to the chassis that will prevent you from pulling the flat panel free so you can rotate it out of the way and access the internals. The latch will be held on by a single screw. You will need a tiny phillips head screw driver with a 90 degree angle at the bit to unscrew the latch and release the flat panel display.

If you don't have access to a small angled screw driver, you may be able to bend the latch out of the way to release the display cable. It is risky, and you wouldn't want to do it unless you there is no other way. You may damage the display cable near the latch so please be careful. I've included a picture of the latch in the image gallery section.

Q: The computer turns on, power LED lights up, but I have no picture or a noisy picture
A: This could be caused by many things, but the most common issue is that the laptop lid open/close switch is just stuck in the on position. The switch, which is located under the cover, next to the floppy drive uses a rather low-quality plastic piece that latched with the screen hinge and is designed to detect when the lid is closed, and will cut the power to the display accordingly. It engages whenever the lid is closed, and since it is near the power supply, a plastic piece inside the switch may slowly deform over time and may get stuck inside the switch. The symptom you will see is a screen that will never seem to turn on when you open the lid, or will have a noisy picture, due to the switch stuck half-on. If you cannot repair the switch manually, the easiest workaround is to just disable it by removing the plastic piece entirely. This will make the screen then stay on regardless if the screen lid is open. Please see the gallery section for an image of the switch.

Replacement BIOS ROM chips

I have started selling replacement 003CH BIOS ROM chips for the T3200SX. If you're currently in need of upgrading your BIOS in order to install a different hard disk, you can use my BIOS chip to get around any limitations you may have with your current BIOS. The BIOS that I am selling is the the 003CH Hybrid BIOS, which is a combination of the 003C BIOS with the faster VGA BIOS of 003I. The hybrid BIOS will essentially act as an older BIOS and allow you to boot any hard disk. With this BIOS, all you need is a disk overlay program to correct the hard drive parameters. I can also program an XT-IDE enabled BIOS chip for you if you wish. Both chips are a drop-in replacement for the old BIOS chip, and should work great in any T3200SX system.

For more information, visit my BIOS ROM chips page.


Files

Documentation

File Size Description
Toshiba T3200SX - Flyer.pdf 8.0 MB Toshiba T3200SX flyer with system specifications.
Toshiba T3200SX - Maintenance Manual.pdf 3.7 MB Toshiba T3200SX maintenance/service manual.
Toshiba - Accessory part list.pdf 26 KB Toshiba Accessory part list

Community Guides

File Size Description
Dumping and Copying Toshiba BIOS ROM 1.9 MB How to dump and copy your BIOS from a T3200SX
This guide will walk you through the steps needed to dump and/or copy a BIOS ROM chip. This manual is especially helpful if you have a BIOS that doesn't accept custom hard drives, and you want to replace it with a version that does work with custom hard disks. Using the steps in this manual you can replace your BIOS with a BIOS version that allows you to use any hard drive in conjunction with the BIOS version found on this site (see download for t3200sx_bios_003ch.zip). An excellent guide written by High Treason.

Note: This guide may apply to other models as well. Use guide at your discretion. You will need a TL866 EEPROM programmer. Highly recommended that you buy a second HN27C1024HG-85 ROM chip and keep your original unmodified and in a safe place.

Operating System

File Size Description
toshiba_dos_3_30.zip 524 KB Toshiba MS-DOS 3.30/R3C60SC bootable disk image

Utilities

File Size Description
tdiagsup_r3ce0.zip 278 KB Toshiba Diagnostics and Supplemental Diskette (R3CE0) for MS-DOS 3.30
tdiagsup_dos50.zip 278 KB Toshiba Diagnostics and Supplemental Diskette for MS-DOS 5.0
test3.zip 21.1 KB TEST3.EXE - Setup program for T3100, T3200, T5100 and T5200 series
xchad.zip 5.3 KB XCHAD.COM - Set Screen Attributes for T3200, T5100 series
HDDID.EXE 1.6 KB Identifies parameters of your IDE HDD
REBOOT.ZIP 243 B Performs cold boot with CTRL+ALT+DEL.
ANYDRIVE.ZIP 13 KB AnyDrive. This program overrides your BIOS HDD parameters so you can utilize up to 504 MB of a hard disk. It installs within the hard-drive's master boot record (MBR).
Due to its very small footprint, this is recommended for Toshiba portables. To install, make a bootable floppy with AnyDrive, FDISK and FORMAT on it. Boot the floppy, install AnyDrive on your HDD, then boot from the HDD to activate Anydrive, but choose floppy boot once it prompts. Then partition with FDISK and run FORMAT to format new partitions. If you have a hard-drive that is larger than 512 MB, you can install AnyDrive by running the command “ANYDRIVE 0 1023 16 63”. This will utilize the first 512 megabytes on the disk. Please note that viruses may overwrite Anydrive in the MBR, so keep your favorite virus scanner and Anydrive handy on a bootable floppy. The reason you can only utilize 512 MB is because of the limitations in the BIOS CHS addressing scheme (1023 cyls, 16 heads, 63 sectors). For more information, see the included text file.
EZDRIVE9.ZIP 423 KB EZ-Drive 9.03W. This program overrides your BIOS HDD parameters so you can utilize up to a 8 GB hard disk. It installs within the hard-drive's master boot record (MBR). Requires 4 MB RAM to run.
View more files on this support site

BIOS ROM dumps

File Size System Description
t3200sx_bios_003ch.zip 47 KB T3200SX 003CH HYBRID BIOS. This Hybrid BIOS ROM has the BIOS from 003C, but the VGA-BIOS from 003I. This Hybrid BIOS will accept any disk installed and VGA graphics are accelerated. It contains the upgraded (and faster) 003I VGA-BIOS. You will only need an overlay program installed such as Anydrive to set/override the BIOS HDD parameters (see ANYDRIVE.ZIP in the Files section). Use a TL866 Minipro programmer or similar to program this on a compatible BIOS chip. Courtesy of High Treason.
t3200sx_bios_pack_1-0.zip 312 KB T3200SX Custom Award BIOS ROM for the T3200SX which includes a patched version of XT-IDE ROM 8-). This ROM will have no trouble identifying and booting any IDE hard disk, no overlay program is required. Courtesy of IanB at Vogons forum. Feel free to visit the forum for the latest version, as the forum is updated more often.
t3200sx_bios_003c.zip 46 KB T3200SX 003C BIOS ROM. This BIOS version does not have a programmed BIOS hard drive exclusion and will accept any hard disk. You will only need an overlay program installed such as Anydrive to set/override the BIOS HDD parameters (see ANYDRIVE.ZIP in the Files section). Use a TL866 Minipro programmer or similar to program this on a compatible BIOS chip.
t3200sx_bios_003e.zip 402 KB T3200SX 003E BIOS ROM. This BIOS version will only accept Conner CP- series hard disks. Curiously this BIOS has the text “T3200SX V3.10 TOSHIBA [..] Copyright (C) 1985-1989 Phoenix Technologies Ltd.[..] FOR EVALUATION ONLY”. Courtesy of RemyV.
t3200sx_bios_003f.zip 44 KB T3200SX/120 003F BIOS ROM from a T3200SX/120 with a Conner 120MB HDD. This BIOS version will only accept Conner CP- series hard disks, and has preset options for 40 MB and 120 MB hard disks.
t3200sx_bios_003h.zip 37 KB T3200SX 003H BIOS ROM. This BIOS version will only accept Conner hard disks. Courtesy of Milan Matijevic. Thank you!
t3200sx_bios_003i.zip 36 KB T3200SX 003I BIOS ROM. The newest known BIOS version for the T3200SX. This BIOS version will only accept Conner hard disks. 003I has been improved with a quicker VGA BIOS than earlier versions. Courtesy of High Treason.


Front with original manuals and driver diskettes.


Rear. I/O ports from left to right: COM1, COM2, LPT1, VGA, ISA.


Left hand side


Right hand side


A look at the System/BIOS setup (003C).


Dead CMOS battery error on power on (003C).


Hand drawn (yeah I drew it in hurry m( ) Screw diagram for servicing the system unit. The picture is missing the two screws that hold the back plastic plate to the case. Also, I've seen two long screws being used to hold the Keyboard EM shield in place. Your mileage may vary.


Scanned version.


Difference between screws compared


Detail of the FPU Cyrix CX-83S87-16-KP FasMath 387 Math coprocessor upgrade found in one T3200SX/120.


003C BIOS ROM chip in socket.


Detail of the 003C BIOS ROM chip in socket.


Detail of the 003C BIOS ROM chip with a coin for size reference. This BIOS version ignores hard disk part numbers and permits use of any IDE hard disk. You will still need an overlay program to override the HDD parameters though.


Image of an original Toshiba T3200SX/120 Conner CP-30104 120 MB hard disk drive and aftermarket Tadiran CMOS clock battery.


003E BIOS ROM chip in socket.


003E BIOS ROM chip in socket (detail).


003F BIOS ROM chip in socket.


003F BIOS ROM chip in socket (detail).


Picture of the internals under the plasma display. Circled in red is the latch securing the display cables and (by extension) the whole display assembly to the chassis.


Detail of the latch (circled) securing the display cables to the chassis. You need to unscrew this latch to gain access to other parts of the laptop, such as the floppy drive and the hard disk drive caddy. See QA above for more information on removing the latch.


Detail image of the sensor switch that detects if the lid is closed. This switch is next to hot components and it may degrade over time and may cause the display to be stuck off or on.


Another image of the lid sensor. Common problem is the pole heats up, bends and then sticks in and prevents the display from turning on, or pops out as seen in this disassembly picture.


Serial number sticker of my European model Toshiba T3200SX. This particular unit was originally sold in Belgium.


Serial number sticker of my US model Toshiba T3200SX.


Serial number sticker of my US model Toshiba T3200SX/120 with a 120MB hard disk.

1) , 5)
Cylinders/Heads/Sectors per track
2) , 6)
Cylinders/Heads/Sectors as reported by BIOS
3)
More information on Conner CP-3000 here
4) , 7)
More information on Conner CP-3044 here
8)
More information on Conner CP-30104 here
9)
Contribution by Jonathan
10)
Affiliate link
toshiba_t-series_support/toshiba_t3200sx.txt · Last modified: 2023-08-31 17:36 by omolini